Loading... Please wait...

Emperor 900 2.5" SATA SSD 16GB-1TB

Hover over image to zoom

  • Image 1
Call 714.460.9844 or Email support@mfactors.com to order
SKU:
Emperor 900
Availability:
Contact 714.460.9844 or support@mfactors.com

 Product Description

­­­­Emperor 900 2.5" SATA Solid State Drive 

Emperor Disk proudly introduces the 2.5" SATA solid state drive (SSD) for many of today's Tablets, UltraBooks, Hybrids NUC and Desktop PCs.

Emperor 900 2.5" SATA SSD delivers all the advantages of Flash Disk technology with Serial ATA I/II/III interface and is fully compliant with the standard 2.5" form factor. Available capacity ranges from 16GB to 1TB. The device is designed based on the standard 7-pin interface for data segment and 15-pin for power segment. The 2.5" SATA runs at a maximum operating frequency of 300MHz with 40MHz external crystal. Based on Toshiba's A19nm Toggle MLC flash (with external DDRIII 256MB/512MB cache enabled and measured by CrystalDiskMark v3.0), Emperor 900 can reach up to 520MB/s read as well as 445MB/s write high performance. Moreover, the 2.5" SATA SSD enables hot-swapping when removing, replacing, or upgrading flash disks while also providing low power consumption in comparison to traditional hard drives.

Offering improved Read/Write performance, SMART technology, reliability, and low power consumption, Emperor 900 2.5" SATA SSD is an ideal storage for embedded systems.

HIGHLIGHTS

  • Easy installation
  • Toshiba A19 MLC NAND Flash
  • Compliant with SATA Revision 3.0
  • Compatible with SATA 1.5Gbps, 3Gbps, 6Gbps interface
  • NCQ support up to queue depth=32
  • Supports power management
  • Supports expanded register for SATA protocol 48 bits addressing mode
  • Embedded BIST function for SATA PHY for low cost mass production
  • Supports all types of MLC large block: 16K/page NAND Flash
  • Supports 2.3 interface and 3.0 interface: 5 channels at maximum
  • Contains 4pcs to 16pcs of TSOP Flash
  • Corrects up to 72bits error in 1K Byte data
  • Supports SMART and TRIM Commands

 

 ***Optional Industrial Grade supporting -45C to 85C and SLC is available (Contact 714.460.9844 or support@mfactors.com) 

Item

Specification

Specification

Interface

SATA 6Gbps and 3Gbps, 1.5Gbps interface

ONFI 2.3 and ONFI 3.0 Interface support 

Electrical 5V (Operating Voltage)

Form Factor

2.5" SATA

SIze

Option 1: 100mm*69.85mm*7mm

Option 2: 100mm*69.85mm*9.5mm

weight

~2oz/0.13lbs

Capacity

16GB~1TB (support 48bit addressing mode)

Performance

Sequential write

445 MB/s

Sequential Read

520 MB/s

Power Dissipation

Idle

305mW  

Active 

4560mW 

Dependability

TRIM 

support 

NCQ 

support 

Firmware Update 

support 

MTBF

>1,000,000 hours

S.M.A.R.T

support

Bad-Block Management

Advanced bad sector management algorithms

Wear-leveling

Static and dynamic wear-leveling algorithms

ECC

Built in hardware ECC circuit (up to 72bit/1KB)

Environment

Storage temperature

-40~85℃

Operation temperature

Standard

0~70 ℃

Industrial

-40~85 ℃

 

 

Vibration 

80Hz~2000Hz/20G 

Shock

1500G/0.5ms

Humidity

90% under 40C

TBW

Terabytes Written: 2591TBW for 1TB

RoHS Compliant

Yes

Warranty

2 years

 Find Similar Products by Tag

2.5" SATA  

 Find Similar Products by Category

 Product Reviews

This product hasn't received any reviews yet. Be the first to review this product!

You Recently Viewed...